How To Clean A Mini Tower Fan

Download Article

Download Commodity

Tower fans accumulate dust and other droppings as they operate. Fortunately, they don't crave a lot of maintenance, as most fans are easily cleaned by brushing off the exterior vent and spraying it with compressed air. You only need to pry open the fan'south casing if the fan still doesn't work properly or begins making noise. Make clean out the fan'due south interior and grease the bearings to continue your home absurd in the summertime.

1
Turn the fan off and unplug it. Prevent the fan's blades from moving while you work. Make sure the plug is out of the wall outlet and you are unable to activate the fan again.^[one]
- Cutting off the power source prevents accidents as well as stops dust from getting deeper within the machine.
ii
Employ a vacuum brush attachment or dust castor to clean the grill. Remove all debris from the exterior casing, paying detail attention to the vents where air enters and exits the fan. The easiest way to do this without scratching the casing is past using the brush attachment on a vacuum cleaner. Clear away as much grit, lint, and other debris as possible.^[two]
- If you don't take a vacuum with a brush attachment, apply a like soft-bristled tool, such equally a grit brush or a microfiber duster.
Advertizement
3
Blow compressed air into the vent to dislodge dust. Aim the canister nozzle direct at the within of the machine past placing information technology straight over the vent. And then, move the nozzle along the vent at a steady rate while releasing the air. Go over the entire vent with the canister.^[3]
- Compressed air is bachelor at many home comeback and office supply stores.
4
Turn the fan on to accident out any remaining dust. Set the compressed air canister aside. Make sure nothing is in the fan'due south vent before you turn it on. Then, plug the power cord back into the wall and let the fan run for a few minutes.
- To forestall grit and debris from filling your habitation, run a vacuum cleaner to selection upward anything that comes out of the fan vent. Alternatively, make clean the fan outside.
Advertisement

one
Unplug the fan and wait for the blades to cease moving. Always turn off the fan earlier attempting to open information technology.^[4] The blades are sharp and tin can be quite dangerous. Wait for the fan to come up to a cease.
- Leave the fan unplugged so it can't activate while you're cleaning it.
2
Remove the screws holding the fan's casing together. Check the front and dorsum ends of the fan for a serial of screws. Most fans take two to four screws, usually above the vent. You will demand a Phillips-head screwdriver. Twist the screws counterclockwise to remove them.^[5]
- The number of screws you need to remove depends on the fan's brand and model.
3
Pull the casing halves apart with a screwdriver. Try to split up the halves with your fingers showtime. Grip the summit part of the example while pulling the forepart console towards you with your other hand. Slide a flat-head screwdriver into the gap betwixt the panels. Work down towards the bottom of the belfry, using the screwdriver to further dissever the panels.^[vi]
- Some tower fans have a summit panel holding the front and back ends together. Pry the top panel upwards first to make loosening the other panels easier.
4
Slide the front panel upwards and away from the tower. Don't pull the panels away correct later on y'all end separating them. The panels attach to one another through a couple of plastic tabs that are very easy to break. Gently elevator the front panel away, leaving the other panels in place.^[7]
- If the tabs interruption, you volition have a much tougher time fitting the panel back in place on the tower. Work slowly to avoid damaging the casing.
v
Spray compressed air into the fan bract to dislodge droppings. Bring the compressed air canister nozzle shut to the top end of the fan blades. The blades await similar a tall, black cylinder that spins within the fan's casing. Start spraying air into the blades, maintaining steady pressure level equally yous motion the nozzle from side to side.
- Yous do not need to remove the fan blades to practise this. Position the nozzle right to a higher place the blades and agree information technology there as you move it.
- Laying the fan down makes the piece of work a fiddling easier. If your fan has a stand attached, consider unscrewing it temporarily in order to rest the fan on a apartment surface.
6
Dust the fan blades with a vacuum brush. ^[8] Utilise a brush attachment on a vacuum cleaner for the most efficient fashion to clean off the blades. Castor the cylindrical cavalcade of blades, rotating it equally needed to reach the other sides. Dislodge whatsoever remaining dust inside the instance.^[9]
- If you lot don't take a vacuum brush use a microfiber material.^[10] You tin also utilize a dust brush, duster, or go over the fan blades again with more compressed air.
seven
Vacuum up the loose dust with a hose attachment. Keep the hose nearby every bit you brush out the inner portion of the tower. If you tin, turn it on while you castor and so information technology picks upwards most of the loose dust coming off the fan blades. Have someone else agree the vacuum hose if needed.^[11]
- If a practiced vacuum isn't bachelor, clean your fan outdoors to prevent the dust and debris from getting into your home. Castor and blow out the fan blades thoroughly.
8
Spray WD-40 or a lubricant on the fan'southward bearings. Wait for silver or black rings on the ends of the fan blade column. They volition exist right above the blades, usually on a metal plate securing the blades to the casing. Spray a few aerosol of the lubricant directly on the ends of each begetting.^[12]
- If your fan makes a lot of noise, the bearings are most likely the cause. These components are responsible for spinning the bract column.
- WD-40 works well as a temporary solution. For something more effective, use car grease or white lithium grease, available at most general, domicile improvement, and machine parts stores.
- You ordinarily practise non demand to have autonomously the fan'south motor to admission these parts. Yet, if you wish to, undo the screws on the summit bearing and the motor at the lesser of the tower. Remove the fan blades and motor, so clean them out thoroughly.
9

Reinstall the components, then exam the fan. Brand sure the bearings and the fan bract are where they need to exist. Put them back if yous removed them, locking them in place with screws every bit needed. Reattach the casing, then plug the fan in and let it run for a few minutes.

Advertisement

Add New Question

Question

How exercise you clean a fan without taking information technology apart?

Alicia Sokolowski is a Green Cleaning Specialist and the President and co-CEO of AspenClean, a green cleaning company in Vancouver, British Columbia. With over 17 years of experience, Alicia specializes in creating a healthier, green culling to chemical-based cleaning products and services. AspenClean develops and manufactures its own line of 100% Natural, EcoCert® certified, and EWG verified™ cleaning products. AspenClean'due south drinking glass cleaner was voted Parent'south Green Option 2020 by readers of the Parents' magazine. Alicia holds a CPA designation and a Bachelor'due south degree in Commerce and Finance from the University of Toronto.

Green Cleaning Specialist

Expert Answer

Enquire a Question

200 characters left

Include your email address to become a bulletin when this question is answered.

Submit

VideoRead Video Transcript

If the fan blades spin but the fan doesn't emit air, cleaning out the blades usually helps.
A squeaking fan often isn't a serious problem. You practise need to open up the fan's casing, merely calculation a lubricant to the bearings gets the fan in working condition once again.
If yous have a hard fourth dimension getting your fan to work, take it to a professional person repair shop. Information technology often means the fan has a bigger problem than dust, such as a burnt-out motor.
To go along your fan running efficiently, clean it out at least once or twice a year.

Advert

Things You'll Need

Grit brush
Compressed air

Phillips-head screwdriver
Flat-head screwdriver
Vacuum cleaner
Brush attachment or dust brush
Compressed air
WD-40 or culling lubricant

About This Article

Article Summary 10

To clean a tower fan, start plough the fan off and unplug it. Then, apply a vacuum with a hose zipper to suck upwards any debris and dust trapped in the grill of the fan. Vacuum the vents on the back of the fan likewise. Next, blow some compressed air into the grill to dislodge whatever stubborn dust trapped in the frame. Plow the fan on to accident out the dust you lot dislodged. To make clean your fan's filter, first open the hatch or unscrew the dorsum of the fan to access the filter. Then, remove the filter and bring it exterior since cleaning the filter can get messy. Utilize a can of compressed air to accident any dirt and grit off of the filter. Then, vacuum the filter with a hose attachment to pull up any deeper layers of dust. Finally, rinse the filter under running water to wash off any remaining dirt and dust, and let it air dry before reinstalling it. For tips on how to take your fan apart if yous can't pull off the front console, keep reading!

Did this summary help you lot?

Thanks to all authors for creating a page that has been read 106,272 times.